Satec PM180 Installation Manual Manuel d'utilisateur

PM180 PM180 Series SUBSTATION AUTOMATION UNIT INSTALLATION MANUAL BG0521 Rev. A4

PM180 Substation Automation Unit 7 Figure 2-6 Three Wire Open Delta Connection Using 2 PTs, 2 CTs (2-element) Wiring Mode = 3OP2 Figure 2-7 F

PM180 Substation Automation Unit 8 Figure 2-8 Three Wire Open Delta Connection Using 2 PTs, 3 CTs (2½-element) Wiring Mode = 3OP3 Figure 2-9

PM180 Substation Automation Unit 9 2.2.6 Digital Inputs 16 optically isolated digital inputs in one digital input module (16DI) are provided for st

PM180 Substation Automation Unit 10 2.2.7 Relays 8 relays in one Relay Output Module (8RO) are provided for alarms, remote control or energy pulsin

PM180 Substation Automation Unit 11 2.2.9 Analog Input/Output The PM180 provides 4 optically isolated analog inputs and 4 analog outputs (4AI/AO) w

PM180 Substation Automation Unit 12 2.2.10 Serial Communication options – COM1, COM2 The PM180 provides 2 optically isolated serial communication p

PM180 Substation Automation Unit 13 2.2.12 Network Communication options ETHERNET 10/100Base TX and 100FX The PM180 provides one 10/100TX Ether

PM180 Substation Automation Unit 14 2.3 Location of Modules The PM180 provides a total of 6 modules slots: 3 fixed slots for ANALOG, CPU and CT fact

PM180 Substation Automation Unit 15 Chapter 3 Serial Communications 3. Communications Figure 3-1 RS-232/RS-422/RS-485 ports locatio

PM180 Substation Automation Unit 16 Computer Connections – RS-232 (COM1) Figure 3-2 RS-232 Simple 3-wire Connection, 9-pin and 25-pin female

PM180 Substation Automation Unit i LIMITED WARRANTY The manufacturer offers the customer a 24-month functional warranty on the instrument for faulty

PM180 Substation Automation Unit 17 Computer Connections – RS-485 (COM1), RS-422/485 (COM2) Figure 3-4 RS-485 Multidrop COM1 Connection, 25-pin PC

PM180 Substation Automation Unit 18 Figure 3-5a RS-485 Multidrop COM2 Connection, 9-pin PC Port Figure 3-6 RS-422 Multidrop COM2 Connection, 25-

PM180 Substation Automation Unit 19 Figure 3-7 RS-422 Multidrop COM2 Connection, 9-pin PC Port

PM180 Substation Automation Unit 20 Chapter 4 Installing the Battery 4. Changing the Battery The PM180 is packed without battery; therefore it

PM180 Substation Automation Unit 21 Appendix: Technical Specifications 5. Appendix: Technical Specifications 5.1 Environmental Conditions Operatin

PM180 Substation Automation Unit 22 5.4 Input Ratings AC Voltage Inputs: V1, V2, V3, VN Measuring range: 57/100 – 400/690 VAC Direct input and input

PM180 Substation Automation Unit 23 Wire Size: 10 AWG (2.5 to 6 mm2) Terminals Pitch: 9.5 mm 5.5 Plug-In I/O Ratings Digital Inputs – 16 Inputs (up

PM180 Substation Automation Unit 24 Accuracy: 0.5% FS Scan time: 2 cycles Wire Size: 12 AWG (up to 2.5 mm2) Terminals Pitch: 5 mm 4 Ana

PM180 Substation Automation Unit 25 Withstanding Insulation: 4kV AC @ 1 mn Connector Type: RJ45 modular. Supported Protocols: MODBUS TCP (Port 502)

PM180 Substation Automation Unit 26 5.9 Log Memory Standard onboard memory: 250 Mbytes. 5.10 Remote Display Module RDM180 (PM180-D model) Display: h

ii Table of Contents Chapter 1 Introduction ...

PM180 Substation Automation Unit 27 5.11 Standards Compliance Directive complied with: EMC: 89/336/EEC as amended by 92/31/EEC and 93/68/EEC LVD: 7

PM180 Substation Automation Unit 28  100 kHz ring wave – 6kV @ 0.5kA  1.2/50 microsecond – 8/20 microsecond Combination Wave – 6kV @ 3kA IEC61

PM180 Substation Automation Unit 29 5.12 Measurement Specifications Parameter Full Scale @ Input Range Accuracy Range % Reading % FS Condition

PM180 Substation Automation Unit 30 Parameter Full Scale @ Input Range Accuracy Range % Reading % FS Conditions Reactive energy1 Import &

PM180 Substation Automation Unit 1 Chapter 1 Introduction 1. Introduction 1.1 About This Manual This manual is intended to assist the user

PM180 Substation Automation Unit 2 • Second backup power supply unit 1.2.1 AC/DC Inputs The PM180 is provided with a set of fully isolated AC/DC i

PM180 Substation Automation Unit 3 Chapter 2 Installation 2. Installation 2.1 Mechanical Installation Figure 2-1a Dimensions Figure 2-1b P

PM180 Substation Automation Unit 4 2.2 Electrical Installation The PM180 is packed without battery; therefore it must be installed by

PM180 Substation Automation Unit 5 Figure 2-3 Three Wire Direct Connection Using 2 CTs (2-element) Wiring Mode = 3dir2 Figure 2-4 Four Wire WY

PM180 Substation Automation Unit 6 Figure 2-5a Four Wire WYE Connection Using 3 PTs, 4 CTs (3-element) Wiring Mode = 4LL3 or 4Ln3 Figure 2-5